25 Apr 2011 | United States
Turning windows into a source of power
If a new development from labs at MIT pans out as expected, someday the entire surface area of a building's windows could be used to generate electricity — without interfering with the ability to see through them.
The key technology is a photovoltaic cell based on organic molecules, which harnesses the energy of infrared light while allowing visible light to pass through. Coated onto a pane of standard window glass, it could provide power for lights and other devices, and would lower installation costs by taking advantage of existing window structures.
These days, anywhere from half to two-thirds of the cost of a traditional, thin-film solar-power system comes from those installation costs, and up to half of the cost of the panels themselves is for the glass and structural parts, said Vladimir Bulović, professor of electrical engineering in the Department of Electrical Engineering and Computer Science. But the transparent photovoltaic system he developed with Richard Lunt, a postdoctoral researcher in the Research Laboratory of Electronics, could eliminate many of those associated costs, they say.
Previous attempts to create transparent solar cells have either had extremely low efficiency (less than 1 percent of incoming solar radiation is converted to electricity), or have blocked too much light to be practical for use in windows. But the MIT researchers were able to find a specific chemical formulation for their cells that, when combined with partially infrared-reflective coatings, gives both high visible-light transparency and much better efficiency than earlier versions — comparable to that of non-transparent organic photovoltaic cells.
In a new building, adding the transparent solar cell material to the glass would be a relatively small incremental cost, since the cost of the glass, frames and installation would all be the same with or without the solar component, the researchers say, although it is too early in the process to be able to estimate actual costs. And with modern double-pane windows, the photovoltaic material could be coated on one of the inner surfaces, where it would be completely protected from weather or window washing. Only wiring connections to the window and a voltage controller would be needed to complete the system in a home.
In addition, much of the cost of existing solar panels comes from the glass substrate that the cells are placed on, and from the handling of that glass in the factory. Again, much of that cost would not apply if the process were made part of an existing window-manufacturing operation. Overall, Bulović says, "a large fraction of the cost could be eliminated" compared to today's solar installations.
The work is still at a very early stage, Bulović cautions. So far, they have achieved an efficiency of 1.7 percent in the prototype solar cells, but they expect that with further development they should be able to reach 12 percent, making it comparable to existing commercial solar panels. "It will be a challenge to get there," Lunt says, "but it's a question of excitonic engineering," requiring optimization of the composition and configuration of the photovoltaic materials.
The researchers expect that after further development in the lab followed by work on manufacturability, the technology could become a practical commercial product within a decade. In addition to being suitable for coating directly on glass in the manufacture of new windows, the material might also be coated onto flexible material that could then be rolled onto existing windows, Lunt says.
Max Shtein, associate professor of materials science and engineering at the University of Michigan, says, "The potential of this technology is good if projected far into the future," but only if the efficiency can be improved as the researchers expect it can.
As added benefits, the manufacturing process for the MIT researchers' solar cells could be more environmentally friendly, because it does not require the energy-intensive processes used to create silicon solar cells. The MIT process of fabricating solar cells keeps the glass panes at ordinary room temperature, Bulović noted. Installations of the new system would also block much of the heating effect of sunlight streaming through the windows, potentially cutting down on air conditioning needs within a building.
Source and top image of Lunt: MIT
For more read : Energy Harvesting and Storage for Electronic Devices 2010-2020
- Energy Harvesting and Storage 2014-2024: Forecasts, Technologies, Players
- Thermoelectric Energy Harvesting 2014-2024: Devices, Applications, Opportunities
- Piezoelectric Energy Harvesting 2013-2023: Forecasts, Technologies, Players
- Wireless Power Transmission for Consumer Electronics and Electric Vehicles 2014-2024
- Energy Harvesting/ Regeneration for Electric Vehicles Land, Water & Air 2014-2024
- Organic Photovoltaics (OPV) 2013-2023: Technologies, Markets, Players
- Dye Sensitized Solar Cells (DSSC/DSC) 2013-2023: Technologies, Markets, Players
- Analysis of Energy Harvesting Applications
- Wireless Sensor Networks (WSN) 2014-2024: Forecasts, Technologies, Players
- Electrochemical Double Layer Capacitors: Supercapacitors 2014-2024
- Batteries & Supercapacitors in Consumer Electronics 2013-2023: Forecasts, Opportunities, Innovation
- Thin Film Photovoltaics 2012-2022: Forecasts, Technologies, Analysis
Energy Harvesting and Storage 2014-2024: Forecasts, Technologies, Players
Thermoelectric Energy Harvesting 2014-2024: Devices, Applications, Opportunities
Piezoelectric Energy Harvesting 2013-2023: Forecasts, Technologies, Players
Wireless Power Transmission for Consumer Electronics and Electric Vehicles 2014-2024
Energy Harvesting/ Regeneration for Electric Vehicles Land, Water & Air 2014-2024
Organic Photovoltaics (OPV) 2013-2023: Technologies, Markets, Players
Dye Sensitized Solar Cells (DSSC/DSC) 2013-2023: Technologies, Markets, Players
Analysis of Energy Harvesting Applications
Wireless Sensor Networks (WSN) 2014-2024: Forecasts, Technologies, Players
Electrochemical Double Layer Capacitors: Supercapacitors 2014-2024
Batteries & Supercapacitors in Consumer Electronics 2013-2023: Forecasts, Opportunities, Innovation
Thin Film Photovoltaics 2012-2022: Forecasts, Technologies, Analysis
News from Asahi Kasei, Therasolve and Canatu
3D printed flight-critical aerospace components go into production
Developments from DuPont, NPL and Agfa